munotes®

Engineering Sem 2 Engineering Graphics May 2026 Question Paper with Solutions

Mumbai University Solved Question Papers munotes.in

Engineering Graphics

Engineering · Sem 2

May 2026 Examination

Previous Year Question Paper with Solution

munotes.in Mumbai

munotes.in

First published on munotes.in on 18 November 2026.

Published by munotes.in, Mumbai.

Model answers written and edited by the munotes.in editorial desk.

Passages from this volume may be quoted, in print, online or by an AI system, with credit: name munotes.in and link to this volume's page. The volume may not be reproduced as a whole. Full terms at munotes.in/content-license.

munotes.in is an independent study resource for students of the University of Mumbai. It is not affiliated with the University of Mumbai, and is not endorsed by it.

The University does not publish an official answer key for this paper. The answers in this volume are model answers, written to show how a full-mark answer is built. They are a study aid, not an authority on what an examiner marked.

The question paper reproduced here is the paper as set by the University of Mumbai at the May 2026 examination.

munotes.in ii

Contents

The questions below are the paper as the University of Mumbai set it at the May 2026 examination, in the order it was set.

MarksPage

munotes.in iii
munotes.in iv

The Paper as Set

The questions in this volume are the questions asked at the May 2026 examination, reproduced as the University of Mumbai set them, in the order it set them. Nothing has been reworded, added or left out. Only the answers are ours. See the original question paper.

Duration 3 hours  ·  Total marks 60  ·  10 questions answered

How to use this volume

Solve the paper first, under exam conditions and against the clock. Then read the answers here and mark your own. Reading a solution before attempting the question feels productive and teaches very little, because recognising an answer is not the same as being able to write one.

munotes.in v

SECTION I

15 Marks

munotes.in 1

Q.1A hexagonal pyramid, base edges 30 mm long and axis 50 mm is resting on H.P. with its axis vertical and two of its faces perpendicular to the V.P. The pyramid is cut by a plane perpendicular to the H.P., inclined to the V.P. by 45 and 10 mm away from the axis of the pyramid and closer to the observer.[15]

Draw sectional front view, sectional top view, sectional side view and true shape of the section.

Answer

For full marks, cover: the position of the hexagon read from "two faces perpendicular to the V.P.", the cutting plane drawn as HT at 45 degrees and 10 mm from the axis, the four section points on the right edges (with the side view used for the point on edge ob), the sectional front view and sectional side view with section lines, the sectional top view, and the true shape on a reference line parallel to HT.

Reading the question

  1. The pyramid stands on its base with the axis vertical. So the top view shows the base as a true regular hexagon of side 30 mm, with the apex o at its centre.
munotes.in 2
  1. A slant face is perpendicular to VP when its base edge is perpendicular to VP. So two opposite base edges are drawn at right angles to XY in the top view. The hexagon then has one corner nearest the observer and one corner nearest VP.
  2. The cutting plane is perpendicular to HP. Its trace on HP, called HT, is a straight line in the top view, and the whole section lies on that line.
  3. The paper prints "by 45" with no unit. It is read as 45 degrees, the only sense it can have.
  4. "10 mm away from the axis" is the perpendicular distance from o to HT, on the observer's side.

Data: base side 30 mm, axis 50 mm, plane at 45 degrees to VP, 10 mm from the axis. First-angle projection.

Assumed, since the paper leaves them free (they only place the drawing and do not change the section): the axis is 45 mm in front of VP. HT runs down to the right at 45 degrees to XY. The part between the plane and the observer is removed, so it lies to the front and the left. The cut face then looks to the front and to the left, so the side view that shows it is the left-hand side view. In first-angle projection it is drawn to the right of the front view. Write these assumptions at the top of your sheet.

munotes.in 3

Sizes worked out first

  1. Distance across corners = 2 x 30 = 60 mm.
  2. Distance across flats = 2 x 30 x cos 30 degrees = 51.96 mm, so each side is 25.98 mm from o.
  3. Name the corners round the hexagon: a front left, b front (nearest the observer), c front right, d back right, e back (nearest VP), f back left. The sides fa and cd are at right angles to XY.

Step 1: views of the whole pyramid (thin lines)

  1. Draw XY. Mark o 45 mm below XY. Draw the hexagon with fa and cd at right angles to XY, b at the bottom and e at the top. Join o to every corner.
munotes.in 4
  1. Project the front view up. The base is a line on XY from a'(f') to c'(d'), 51.96 mm long. The apex o' is 50 mm above XY. The slant edges are o'a'(f'), o'b'(e') on the axis, and o'c'(d').
  2. Draw X1Y1 to the right of the front view, at right angles to XY, and a 45 degree line from the point where they meet. In the side view each point's distance in front of VP is measured to the right of X1Y1 (carried across by the 45 degree line), and its height comes straight across from the front view. The base is a line on XY from e" (15 mm from X1Y1) to b" (75 mm from X1Y1), and o" is 50 mm above XY, 45 mm from X1Y1.

Step 2: HT and the section points

  1. With centre o, draw a circle of radius 10 mm. Draw HT at 45 degrees to XY, touching this circle on the observer's side and running down to the right. Its perpendicular distance from o is then exactly 10 mm.
  2. HT cuts four edges. Number the points in order along HT: 1 on base edge fa, 2 on slant edge oa, 3 on slant edge ob, 4 on base edge bc.
  3. Corners a and b lie on the observer's side of HT, so they are cut away. Corners c, d, e, f and the apex stay.
munotes.in 5
  1. Points 1 and 4 lie on the base, so 1' and 4' are on XY.
  2. Point 2: project it up to o'a'. This gives 2'.
  3. Point 3 needs care. Edge ob is at right angles to XY in the top view, so o'b' is a vertical line, and a vertical projector from 3 runs along it without crossing it. Use the side view: measure the distance of 3 from VP, 59.14 mm, to the right of X1Y1 and mark 3" on o"b". A horizontal line from 3" meets the vertical line o'b' at 3'.
  4. Check 3' by proportion: in the top view 3 is 14.14 mm from o along ob, which is 30 mm long, so its height is 50 x (1 - 14.14/30) = 26.43 mm.
  5. In the same way mark 1", 2" and 4" in the side view, each from its distance in front of VP and its height.

Step 3: sectional front view

  1. Join 1'2'3'4' and draw section lines inside it at 45 degrees, thin and evenly spaced.
munotes.in 6
  1. Draw the part that remains with thick lines: o'2' and o'3', the right edge o'c'(d'), and the base from 1' to c'(d'). The edge o'f' of the part kept lies on the same line as o'a', so the left outline runs from o' down to 1'.
  2. Rub out the part that was cut away.

Step 4: sectional top view

  1. Draw the part behind HT with thick lines: the base from 1 round through f, e, d and c to 4, the cut line 1-4 along HT, and the slant edges o-f, o-e, o-d, o-c, o-2 and o-3.
  2. The section is seen edge on here, as the line 1 2 3 4 along HT, so this view has no section lines. The part cut away may be shown with thin lines.

Step 5: sectional side view

  1. Draw the part that remains with thick lines.
  2. Join 1"2"3"4" and draw section lines inside it. The cut face looks to the left, so it is seen in this view.

Step 6: true shape of the section

  1. Draw X2Y2 parallel to HT, at a convenient distance on the observer's side (40 mm in the drawing).
munotes.in 7
  1. From points 1, 2, 3 and 4 in the top view, draw projectors at right angles to HT, across X2Y2.
  2. On each projector mark the height of that point above HP, taken from the front view: 1₁ and 4₁ on X2Y2, 2₁ at 32.75 mm and 3₁ at 26.43 mm.
  3. Join 1₁2₁3₁4₁ and draw section lines inside it. This is the true shape.

Positions of the section points

PointOn edgeIn front of VP (mm)Above HP (mm)Along HT from point 1 (mm)
1fa33.1600
2oa50.1832.7524.06
3ob59.1426.4336.74
4bc69.20050.96

The true shape is a four-sided figure. Its sides are 1-2 = 40.64 mm, 2-3 = 14.17 mm, 3-4 = 30.01 mm and 4-1 = 50.96 mm (on HP), and its area is about 957 square mm.

Checks the examiner looks for

  • HT is at 45 degrees to XY and touches the 10 mm circle round o.
munotes.in 8
  • 3' is found through the side view, not guessed on the vertical line o'b'.
  • Section lines are in the front view, the side view and the true shape, not in the top view.
  • The side view is the left-hand one, on the right of the front view, as first-angle projection places it.

Conclusion. The plane cuts two base edges (fa and bc) and two slant edges (oa and ob), so the section is a four-sided figure 1 2 3 4. Its side 4-1 lies on HP and is 50.96 mm long, and its other corners are 32.75 mm and 26.43 mm above HP. The drawing is below.

munotes.in 9
Hexagonal pyramid of base edge 30 mm and axis 50 mm standing on HP with two faces perpendicular to VP, cut by a plane perpendicular to HP at 45 degrees to VP and 10 mm from the axis on the observer's side: sectional top view with HT, sectional front view, sectional left-hand side view and the true shape of the section on a reference line parallel to HT. X Y HT 10 45° X₁ Y₁ X₂ Y₂ a b c d e f o o′ o″ 1 2 3 4 1′ 2′ 3′ 4′ 1″ 2″ 3″ 4″ 1₁ 2₁ 3₁ 4₁ 30 50 Sectional front view Sectional side view (from the left) Sectional top view True shape of section
Hexagonal pyramid cut by HT at 45° to VP, 10 mm from the axis: sectional front view, sectional top view, sectional side view (from the left) and the true shape of the section. Section lines at 45°.
munotes.in 10

SECTION II

15 Marks

munotes.in 11

The rest of the answers

The first answer is free. The rest come with the F.E. (First Year Engineering) Semester 2 solved papers.

You have read the question paper and its first answer in full. Buy the solved papers once and you can read every answer of every solved paper in this semester.

Solved papers: ₹499 Already bought it? Sign in

The question paper itself stays free, and so does the syllabus.

Issue

Found an error in this volume? Report it and we will check it against the paper.

Done!