munotes®

Engineering Sem 2 Engineering Graphics May 2025 Question Paper with Solutions

Mumbai University Solved Question Papers munotes.in

Engineering Graphics

Engineering · Sem 2

May 2025 Examination

Previous Year Question Paper with Solution

munotes.in Mumbai

munotes.in

First published on munotes.in on 18 November 2026.

Published by munotes.in, Mumbai.

Model answers written and edited by the munotes.in editorial desk.

Passages from this volume may be quoted, in print, online or by an AI system, with credit: name munotes.in and link to this volume's page. The volume may not be reproduced as a whole. Full terms at munotes.in/content-license.

munotes.in is an independent study resource for students of the University of Mumbai. It is not affiliated with the University of Mumbai, and is not endorsed by it.

The University does not publish an official answer key for this paper. The answers in this volume are model answers, written to show how a full-mark answer is built. They are a study aid, not an authority on what an examiner marked.

The question paper reproduced here is the paper as set by the University of Mumbai at the May 2025 examination.

munotes.in ii

Contents

The questions below are the paper as the University of Mumbai set it at the May 2025 examination, in the order it was set.

MarksPage

munotes.in iii
munotes.in iv

The Paper as Set

The questions in this volume are the questions asked at the May 2025 examination, reproduced as the University of Mumbai set them, in the order it set them. Nothing has been reworded, added or left out. Only the answers are ours. See the original question paper.

Duration 3 hours  ·  Total marks 60  ·  9 questions answered

How to use this volume

Solve the paper first, under exam conditions and against the clock. Then read the answers here and mark your own. Reading a solution before attempting the question feels productive and teaches very little, because recognising an answer is not the same as being able to write one.

munotes.in v

Q1

Solve ANY ONE questions from following: a and b, OR a and b 15 Marks

munotes.in 1

aDraw the involute of a circle, 40 mm in diameter. Also, draw the tangent and normal at a point on the curve at a distance of 100 mm from the center of the circle.[9]

Answer

For full marks, cover: the length of string for one turn, the construction by 12 divisions, a smooth curve, the point M found with an arc of radius 100, the normal through the point where it touches the circle, and the tangent at right angles to it.

What the curve is

An involute is the curve traced by the end of a tight string as it is unwound from a circle. At every instant the straight part of the string touches the circle, and its length equals the arc already unwound. One full turn of the string uses the whole circumference.

Data: diameter D = 40 mm, so radius r = 20 mm. The point M lies on the curve with OM = 100 mm, where O is the centre.

Numbers worked out first

  1. Circumference = pi x D = 3.1416 x 40 = 125.66 mm. This is the length of string for one turn.
munotes.in 2
  1. Divide the circle into 12 equal parts of 30 degrees. Each part holds 125.66 / 12 = 10.47 mm of string.
  2. At the k-th division the free end is k x 10.47 mm from the point where the string leaves the circle.
PointLength of string off the circle (mm)
P110.47
P220.94
P331.42
P441.89
P552.36
P662.83
P773.30
P883.78
P994.25
P10104.72
P11115.19
P12125.66

Construction of the involute

  1. Draw the circle of diameter 40 mm with centre O. Mark A at the bottom of the circle.
munotes.in 3
  1. Draw the tangent at A. Mark on it the length 125.66 mm and divide it into 12 equal parts of 10.47 mm.
  2. Divide the circle into 12 equal parts from A and number the points 1 to 12, going the way the string unwinds.
  3. At points 1 to 11 draw tangents to the circle, all on the same side.
  4. On the tangent at point k, mark the length k x 10.47 mm (k parts of the divided line). This gives P1 to P11. P12 is the far end of the line drawn at A.
  5. Join A, P1, P2 and so on to P12 by a smooth curve. This is the involute of the circle.

The point M at 100 mm from the centre

  1. With O as centre and radius 100 mm, draw an arc. It cuts the involute at M.
munotes.in 4
  1. Check with numbers: a point of the involute at distance OM from the centre has a string of length sqrt(OM squared - r squared) off the circle. Here sqrt(100 squared - 20 squared) = 97.98 mm.
  2. That string has unwound 97.98 / 20 = 4.899 radians, which is 280.69 degrees. So M lies between P9 (270 degrees) and P10 (300 degrees), as the drawing shows. P9 is 96.35 mm from O and P10 is 106.61 mm, and 100 lies between them.

The normal and the tangent at M

The normal to an involute at any point is the string at that instant. The string touches the circle, so the normal at M is the line from M that touches the circle.

  1. Join O to M. Find C, the midpoint of OM.
  2. With C as centre and radius CO = 50 mm, draw a semicircle on OM. It cuts the base circle at N.
  3. The angle ONM is 90 degrees (angle in a semicircle), so MN touches the circle at N. MN is the normal at M. Its length is 97.98 mm, the string length found above.
  4. Through M draw a line at right angles to MN. This is the tangent to the involute at M.
  5. Mark the right angle at M, and name the two lines NORMAL and TANGENT.
munotes.in 5

Points the examiner checks

  • The string length 125.66 mm and its 12 equal parts are shown.
  • The curve is smooth and passes through every point P1 to P12.
  • M is found by the arc of radius 100 mm, and the normal touches the circle at N.
  • The tangent is at 90 degrees to the normal at M.
  • Construction lines are thin; the curve, the normal and the tangent are drawn clearly.

Conclusion. The involute of the 40 mm circle is drawn for one full turn of 125.66 mm. At M, 100 mm from the centre, the normal MN touches the circle at N and is 97.98 mm long. The tangent at M is at right angles to MN. The drawing is below.

munotes.in 6
Involute of a circle of 40 mm diameter for one full turn, by the 12-division method, with the normal and the tangent drawn at the point M of the curve that is 100 mm from the centre. O πD = 125.66 (12 parts of 10.47) 1 P₁ 2 P₂ 3 P₃ 4 P₄ 5 P₅ 6 P₆ 7 P₇ 8 P₈ 9 P₉ 10 P₁₀ 11 P₁₁ P₁₂ A R 100 C N M NORMAL TANGENT ϕ40 Involute of the ϕ40 circle, one full turn: A, P₁ ... P₁₂ OM = 100, MN = 97.98 is the normal, the tangent is at 90° to MN at M
Involute of the ϕ40 circle (A to P₁₂) with the normal MN and the tangent at M, where OM = 100 mm.
munotes.in 7

The rest of the answers

The first answer is free. The rest come with the F.E. (First Year Engineering) Semester 2 solved papers.

You have read the question paper and its first answer in full. Buy the solved papers once and you can read every answer of every solved paper in this semester.

Solved papers: ₹499 Already bought it? Sign in

The question paper itself stays free, and so does the syllabus.

Issue

Found an error in this volume? Report it and we will check it against the paper.

Done!