munotes®

Engineering Sem 2 Engineering Graphics Dec 2025 Question Paper with Solutions

Mumbai University Solved Question Papers munotes.in

Engineering Graphics

Engineering · Sem 2

Dec 2025 Examination

Previous Year Question Paper with Solution

munotes.in Mumbai

munotes.in

First published on munotes.in on 18 November 2026.

Published by munotes.in, Mumbai.

Model answers written and edited by the munotes.in editorial desk.

Passages from this volume may be quoted, in print, online or by an AI system, with credit: name munotes.in and link to this volume's page. The volume may not be reproduced as a whole. Full terms at munotes.in/content-license.

munotes.in is an independent study resource for students of the University of Mumbai. It is not affiliated with the University of Mumbai, and is not endorsed by it.

The University does not publish an official answer key for this paper. The answers in this volume are model answers, written to show how a full-mark answer is built. They are a study aid, not an authority on what an examiner marked.

The question paper reproduced here is the paper as set by the University of Mumbai at the Dec 2025 examination.

munotes.in ii
munotes.in iii
munotes.in iv

The Paper as Set

The questions in this volume are the questions asked at the Dec 2025 examination, reproduced as the University of Mumbai set them, in the order it set them. Nothing has been reworded, added or left out. Only the answers are ours. See the original question paper.

Duration 3 hours  ·  Total marks 60  ·  9 questions answered

Instructions printed on the paper

  • Note: 1) Question No. 1 is compulsory. 2) Attempt any three questions out of the remaining five questions. 3) Figures to the right indicate full marks. 4) Assume suitable data wherever required, but justify the same.

How to use this volume

Solve the paper first, under exam conditions and against the clock. Then read the answers here and mark your own. Reading a solution before attempting the question feels productive and teaches very little, because recognising an answer is not the same as being able to write one.

munotes.in v

Q1

Attempt any ONE 15 Marks

munotes.in 1

A.Figure 1 shows an isometric view of a block. Draw the following: a) Sectional front view (F.V.) looking along arrow Y (Section B-B) b) Right-hand side view (R.H.S.V) c) Top View (T.V).[15]

[Figure 1, an isometric view, prints the dimensions 120, 70, 30, 20, 10 and 10 on the base and its right end; 20 and 40 on the left upright with the note "ϕ20 HOLE"; 10 and 20 at a rib; 40, 40, R25, ϕ40 and 10 on the block with the rounded top and its hole; arrow Y on the long front face and the cutting plane B-B along the length]

Answer

For full marks, cover: the block read correctly from Figure 1, the sizes you had to assume written on the sheet with their reasons, first-angle layout (side view on the left of the front view, top view below it), the section on B-B with section lines at 45 degrees and no hidden lines in it, hidden lines in the top view, centre lines, the cutting plane B-B in the top view, and the printed sizes on the views.

munotes.in 2

Reading Figure 1

Arrow Y looks at the long face, so that face is the front. Lengths run from the left end, depths run back from the front face, and heights run up from the bottom. All sizes are in mm.

  1. Base: 120 long, 70 deep and 20 high.
  2. Groove under the base: 30 wide and 10 deep. It is 10 from the back face, so it lies between 30 and 60 from the front face.
  3. Raised part: on the base stands a part 100 long and 40 high, from the left end. Its top is 20 + 40 = 60 above the bottom.
  4. Upright: the first 20 of the raised part rise higher, with a round top. This is the upright at the left end.
  5. Bearing block: 40 long, with a round top of R25. Its right face is 20 from the right end of the base. So it lies between 60 and 100 from the left end.
  6. Lengths along the base: upright 20, gap 40, block 40, and 20 of bare base at the right end. 20 + 40 + 40 + 20 = 120.
munotes.in 3
  1. Hole: the ϕ20 hole runs on one axis through the upright and the block. The axis is 40 above the base, so it is 60 above the bottom. Between the upright and the block, the top of the raised part is at the axis height. So there the hole is open at the top, as a half-round channel 20 wide. These are the two lines drawn along the top in Figure 1.
  2. Counterbore: ϕ40 and 10 deep, in the right face of the block.
  3. Rib: 10 thick. Its right face is 20 from the block's right face, so it lies between 70 and 80 from the left end. It is a triangle in front of the block.
  4. Plane B-B: the vertical plane along the length, through the hole axis. Both B arrows lie on it. The part in front of it is removed, and the rest is seen along arrow Y.

Sizes not printed, and what is assumed

Note 4 of the paper says: "Assume suitable data wherever required, but justify the same." Figure 1 leaves four things without a size. Write these four lines on your sheet.

munotes.in 4
  1. The upright's round top is R25. Figure 1 prints R25 only on the block. The upright's round top is drawn the same size, on the same axis. So it is taken as R25 too.
  2. The upright and the block are 50 wide, flush with the back face of the base. 50 = 2 x 25, the width of an R25 round top. Figure 1 draws both flush with the back face. So they stand 70 - 50 = 20 back from the front face. The hole axis is 70 - 25 = 45 from the front face.
  3. The groove runs right through the 120 length. No length is printed for it. A groove that stops short would need a printed length.
  4. The rib is 20 deep and 40 high. Its sloping edge runs from the front edge of the base top up to the block's front face. Figure 1 draws it ending where the block's flat front face meets the round top, 40 above the base. The 20 is the gap in front of the block (assumption 2).

Each of these agrees with every printed size and with the way Figure 1 is drawn.

munotes.in 5

Construction

Use first-angle projection. Draw the front view first. Draw the right-hand side view on its left and the top view below it, joined by thin projectors. In the side view and the top view, the front of the block is the side away from the front view.

a) Sectional front view on B-B (looking along arrow Y)

  1. Draw the base, 120 long and 20 high. The plane B-B passes through the groove, so only the top 10 of the base is cut there. Below it, the back face of the groove shows as a plain strip 10 high.
  2. On the base, draw the raised part, 100 long and 40 high, from the left end.
  3. Draw the upright (the first 20) and the block (60 to 100 from the left end). Both rise to 60 + 25 = 85 above the bottom. The plane cuts each round top through its highest line, so its top shows as a straight line.
  4. Draw the hole. The plane cuts it along its axis. So in the upright and in the block it shows as a band 20 high, from 50 to 70 above the bottom.
  5. Between the upright and the block, the cut face stops at 50, the bottom of the channel. Above it, the far half of the channel shows up to the top of the raised part, 60 above the bottom.
munotes.in 6
  1. Draw the counterbore at the block's right face: 40 high (from 40 to 80 above the bottom) and 10 deep.
  2. Hatch every cut face with thin lines at 45 degrees, about 3 apart, all the same way, because the block is one piece. Do not hatch the hole, the counterbore or the groove, because they are empty. The rib is in front of the plane, so it is removed and does not show.
  3. Draw the hole axis as a centre line. Show no hidden lines in a sectional view. Write SECTION B-B under the view.

b) Right-hand side view (on the left of the front view)

  1. Draw the right end of the base, 70 wide and 20 high. Cut the groove into its bottom: 30 wide and 10 deep, 10 from the back. The groove runs through, so its outline is a visible line.
  2. Draw the block's right face: 50 wide at the back, straight up for 40 from the base top, then the R25 round top. Its centre is 60 above the bottom and 45 from the front.
  3. On the same centre, draw the counterbore ϕ40 and the hole ϕ20 as two full circles.
munotes.in 7
  1. Draw the rib in front of the block: a triangle 20 wide and 40 high. Its sloping edge runs from the front edge of the base top to the top of the block's flat front face.
  2. The upright is behind the block and has the same outline, so it adds no line. Every edge in this view is visible, so it has no hidden lines.
  3. Draw the centre lines of the circles.

c) Top view (below the front view)

  1. Draw the base, 120 x 70.
  2. Draw the upright (20 long) and the block (40 long) at the back, each 50 deep, with the raised part's top between them.
  3. Between the upright and the block, draw the open channel: two lines 20 apart, 35 and 55 from the front.
  4. Draw the rib in front of the block: 10 long and 20 deep, between 70 and 80 from the left end.
munotes.in 8
  1. Draw the hidden edges as dashed lines. The groove under the base: 30 and 60 from the front, the full length. The hole inside the upright and the block: 35 and 55 from the front. The counterbore: 25 and 65 from the front, 10 long at the block's right face.
  2. Draw the cutting plane B-B: a chain line along the length, 45 from the front, thick at its two ends. At each end add an arrow pointing to the back, the way the section is seen, and the letter B.
PartSize (mm)Where
Base120 x 70 x 20at the bottom
Groove30 wide, 10 deep, right through10 from the back face
Raised part100 x 50 x 40from the left end, at the back
Upright20 thick, R25 top (assumed)left end
Bearing block40 long, R25 top20 from the right end
Holeϕ20, right throughaxis 60 above the bottom, 45 from the front
Counterboreϕ40, 10 deepblock's right face
munotes.in 9
PartSize (mm)Where
Rib10 thick, 20 deep, 40 highbetween 70 and 80 from the left end
Overall height20 + 40 + 25 = 85top of the round tops

Conclusion. The sectional front view on B-B shows the block cut along the hole axis, with the hole, the counterbore and the open channel left unhatched. The right-hand side view, on the left, shows the round top, the circles of the counterbore and the hole, the rib and the groove. The top view, below, shows the cutting plane B-B and the hidden groove, hole and counterbore. The drawing is below.

munotes.in 10
Figure 1 block: sectional front view on the plane B-B through the hole axis, seen along arrow Y, with the right-hand side view on its left and the top view below it, first angle projection, with the main sizes. B B 20 40 40 20 10 10 20 40 20 30 10 70 R25 ϕ40 ϕ20 HOLE 10 20 120 SECTIONAL FRONT VIEW (SECTION B-B) RIGHT-HAND SIDE VIEW TOP VIEW
Figure 1: sectional front view (Section B-B, seen along arrow Y), right-hand side view and top view, first angle. Section lines at 45°.
munotes.in 11

The rest of the answers

The first answer is free. The rest come with the F.E. (First Year Engineering) Semester 2 solved papers.

You have read the question paper and its first answer in full. Buy the solved papers once and you can read every answer of every solved paper in this semester.

Solved papers: ₹499 Already bought it? Sign in

The question paper itself stays free, and so does the syllabus.

Issue

Found an error in this volume? Report it and we will check it against the paper.

Done!